Which torch are you using?

The Small is the 3-LED model powered by two AA batteries. The compartment opens at the tail cap.

1. 01

   Switch off and open

   Hold the body firmly and turn the tail cap anti-clockwise. Keep the lanyard clear of the threads.

2. 02

   Remove the old pair

   Slide both AA batteries out. Wipe away dust or moisture; do not scrape the metal contacts.

3. 03

   Fit two matching AA batteries

   Use two fresh batteries of the same brand and type. Follow the + / − marks inside the body.

4. 04

   Close and test

   Turn the cap clockwise until snug, then press the rear button once. If it stays dark, reopen and check the + / − markings.

This rubber-coated everyday torch uses AA batteries. Follow the quantity and + / − markings inside its own battery carrier.

1. 01

   Read the carrier first

   Open the battery end and check the diagram inside before buying or fitting batteries. Use these markings for both the number of batteries and their direction.

2. 02

   Fit one matched set

   Use a complete set of fresh AA batteries. Do not mix old and new batteries or different types.

3. 03

   Seat the cap squarely

   Start the cap gently so the threads do not cross, then tighten until the body closes without a gap.

4. 04

   Press once to test

   Use the single button for on / off. If the beam flickers, re-seat the batteries and check that the cap is fully home.

The Large is the longest rubber-bodied torch and uses three D batteries. Support the body on a flat surface while changing them.

1. 01

   Lay the torch flat

   Switch off and use a stable, dry surface. Turn the end cap anti-clockwise while supporting the body.

2. 02

   Remove all three batteries

   Slide the D batteries out one at a time. Inspect the long compartment and spring before reloading.

3. 03

   Fit three matching D batteries

   Follow every + / − mark. The middle battery is easy to reverse, so check all three + / − markings before closing.

4. 04

   Close without forcing

   Engage the threads squarely, tighten clockwise until snug, then press the push button to test the selected 3- or 7-LED head.

The 3-LED and 7-LED Medium torches are set up in the same way. Both use two D batteries.

1. 01

   Open the base

   Switch off, place the torch on a dry surface and turn the end cap anti-clockwise.

2. 02

   Remove both D batteries

   Tip the body gently and catch the batteries. Check the compartment for leakage, corrosion or damp.

3. 03

   Load two fresh D batteries

   Follow the + / − markings and keep both batteries the same brand, type and age. If a battery is not sitting flat, stop and check its direction before closing the cap.

4. 04

   Seal and test

   Turn the cap clockwise until secure. Press the button and check that every LED in the head illuminates.

Start with the rechargeable battery. The AAA adaptor is the emergency backup; keep it and the charging cable in the case.

1. 01

   Fit one power source

   Unscrew the body and fit the supplied Li-ion battery to the + / − markings. Use the AAA adaptor only as an alternative power source—never alongside the Li-ion battery.

2. 02

   Charge before the first trip

   Connect the supplied USB-A to USB-C cable. Leave the torch on a dry surface until the charge indicator shows it is complete.

3. 03

   Choose spot or flood

   Use the main switch to cycle the white-light modes. Adjust the head to move from a wide flood for nearby work to a focused spot for distance.

4. 04

   Use the side light deliberately

   Cycle to the ambient side light for a tent or work area, red for preserving night vision, and strobe only for emergency signalling.

5. 05

   Use the powerbank

   Connect a compatible phone cable to the output port. Replace the port cover after use to protect it from grit and moisture.

This 110mm model takes three AAA batteries and has an adjustable beam. Before first use, remove the plastic transport tab if one is fitted.

1. 01

   Unscrew the tail cap

   Turn the base anti-clockwise. On first use, check for a clear disc or paper strip between the batteries and the contact.

2. 02

   Remove any plastic transport tab

   Pull it out completely before switching on. The tab prevents accidental activation in transit and is not refitted.

3. 03

   Check all three batteries

   Match the supplied AAA batteries to the + / − diagram. When they run down, replace all three together.

4. 04

   Switch on and adjust the beam

   Tighten the cap and press the button. Move the focus head between a broad flood and a narrow spot beam.

These are C / R14 batteries. Open the pack only after checking that your device is marked for C batteries.

1. 01

   Read the device marking

   Look for C, R14 or the matching battery silhouette inside the compartment.

2. 02

   Check every + / − marking

   Insert the positive button and flat negative end exactly as shown by the device diagram.

3. 03

   Replace the complete set

   Do not combine partly used batteries with new ones, or mix Greencell batteries with a different chemistry.

4. 04

   Store unopened batteries correctly

   Keep the pack cool and dry, away from loose metal objects and out of reach of children.

5. 05

   Recycle after use

   Remove exhausted batteries promptly and take them to a battery collection point; never put them in a fire.

This bundle includes the 7-LED Medium and 7-LED Large. The Medium uses two D batteries; the Large uses three.

1. 01

   Sort the two matched sets

   Prepare two D batteries for the Medium and three D batteries for the Large. Keep the two-battery and three-battery sets separate.

2. 02

   Load and close separately

   Follow the + / − markings inside each body and close each tail cap squarely.

3. 03

   Check all seven LEDs

   Switch on each torch and look directly at the head only while it is off. If one LED is dark, switch off and re-seat the cap and batteries.

4. 04

   Store for the intended job

   Keep the Medium as the easier carry; reserve the Large for the jobs where the longer battery stack is useful.

This USB-C rechargeable COB light combines a carabiner, bottle opener, window breaker and optional tripod.

1. 01

   Charge through USB-C

   Open the port cover and connect a USB-C cable. Charge on a dry, non-flammable surface, then close the cover.

2. 02

   Cycle the light modes

   Press the power button repeatedly to move through the available COB settings; stop on the lowest level that suits the task.

3. 03

   Clip it safely

   Use the carabiner on a belt, bag or tent loop. Make sure the clip closes fully and does not press the power button.

4. 04

   Set the tripod

   On the tripod version, open the legs on a level surface and seat the light firmly before aiming it.

5. 05

   Use tools unlit

   Switch the lamp off before using the bottle opener or window-breaker point so the lens stays away from the work.

This 4mm magnetic light is momentary by design: it stays on only while you hold the button.

1. 01

   Place or hold it

   Grip the edge, or attach the magnetic back to a clean steel surface such as a fridge, toolbox or bonnet.

2. 02

   Press continuously

   Hold the button for light. The switch does not latch; releasing it turns the dual LEDs off.

3. 03

   Store it flat

   Keep it dry and away from keys or objects that could hold the button down inside a bag.

4. 04

   Retire the whole light

   The fitted CR2016 batteries are not replaceable. Do not split or pry open the sealed body when they are exhausted.

Both torches use D batteries: two in the Medium and three in the Large.

1. 01

   Identify by body length

   The Medium is the shorter RT5149. The Large RT5150 has the longer battery tube and larger head.

2. 02

   Count before loading

   Set out two D batteries for the Medium and three D batteries for the Large. Keep each matched set together.

3. 03

   Check both battery directions

   Load each torch to its own internal marks and check the middle batteries before closing.

4. 04

   Test and label storage

   Press both buttons, then store the Large for long-run jobs and the Medium where a lighter all-rounder is easier to grab.

This USB-C rechargeable COB light clips to a cap, bag, book, clothing or tool pouch.

1. 01

   Charge via USB-C

   Connect the supplied cable with the lamp switched off. Disconnect it before clipping the lamp to clothing.

2. 02

   Clip onto a firm edge

   Push the clip fully over a cap brim, strap, pocket or book cover so the light cannot twist free.

3. 03

   Aim before selecting a mode

   Point the COB panel away from faces, then press the control to cycle through its lighting settings.

4. 04

   Use the lowest useful mode

   A lower mode is better for reading and close tasks; brighter settings suit walking or work areas.

5. 05

   Remove before washing

   Unclip the light from clothing, caps or bags before washing or soaking them.

The shorter 95mm Mini uses three AAA batteries and produces a fixed, broad COB beam. It does not have an adjustable focus.

1. 01

   Unscrew the base

   Hold the rubber body and turn the tail cap anti-clockwise.

2. 02

   Check all three AAA batteries

   Remove any plastic transport tab and confirm the batteries match the + / − markings.

3. 03

   Close the cap

   Turn clockwise until snug. Do not overtighten the small plastic threads.

4. 04

   Use the push button

   Press once for the fixed wide COB beam and again to switch off.

Charge the built-in 1200mAh battery, adjust the strap, then use the lamp button to choose bright, low or strobe.

1. 01

   Charge at the base

   Connect the USB-C cable to the port on the lamp body. The indicator changes from red to green when complete.

2. 02

   Fit the strap

   Place the lamp centrally on the forehead and shorten the strap until secure without pressure.

3. 03

   Aim before switching on

   Tilt the lamp down toward the path or work surface so the first bright mode does not dazzle another person.

4. 04

   Cycle the three modes

   Press for bright, low and strobe. Use low for close work and strobe only for emergency visibility.

5. 05

   Dry before charging

   After rain or exercise, wipe the lamp and port area and allow them to dry before connecting USB-C.

The two torches use different batteries: two AA for the Small and two D for the Medium.

1. 01

   Separate the two sizes

   The shorter, narrower torch is the Small RT5148; the thicker body is the Medium RT5149.

2. 02

   Load the Small

   Open its tail cap and fit two matching AA batteries to the + / − markings.

3. 03

   Load the Medium

   Open the larger cap and fit two matching D batteries. Do not transfer AA batteries or improvised spacers into this body.

4. 04

   Test both buttons

   Close each cap snugly and test each torch independently before splitting them between car and home.

This USB-C work light has a 180° folding head, dimmable COB panel, magnetic base and hanging hook.

1. 01

   Charge before folding away

   Connect the supplied USB-C cable with the light switched off. Disconnect and close the port before use.

2. 02

   Choose the light source

   Use the control to select the broad inspection panel or the end flashlight for a narrow gap.

3. 03

   Set the angle

   Fold the head through the needed angle; stop at its natural positions rather than forcing the hinge.

4. 04

   Mount hands-free

   Place the magnetic base on clean steel or use the hanging hook. Tug gently to confirm it is secure before releasing.

5. 05

   Dim for reflective work

   Reduce the COB output around polished engine parts or mirrors to cut glare and extend battery life.